Avisynth Use on Intel Macs

[Bloodworth]

I'm terribly sorry, I didn't remember who started this topic and decided not to go back and check, to my humiliation -_-

I'll keep you posted on .AVI support as I work...

One last thing, at the end of my .AVS I have ConvertToRGB32() or whatever that line is. In VirutalDub when I choose huffyuv as the compressor (fast recompress - on) does it keep it in RGB32, or is it doing more color conversions? I would rather not convert more than YUVx (DVD SOURCE) --> RGB32 (AVI FOOTAGE) --> YUV12 (FINAL MASTER), so I was wondering if I'm adding more conversions with this method?

[Kawatta-kun]

Meaning, using crossover then through that using AMVaap it will alow encoding?
What about codecs, stay on crossover but to they "go" to NLE's awell?

Cause i asked something like: http://www.animemusicvideos.org/forum/v ... 1&t=104515

[Kionon]

This depends upon what step you mean by "encoding." Codecs need to be applied both inside and outside of the crossover/wine environment.

As long as you can find a mac version of the codec, then its use inside of and outside of the environment, as in the case say vdubmd vs final cut pro, will be possible. Last time I checked, and I should maybe do more research again, the one lossless codec that meets this criterion is HUFFYUV.

If by encoding you mean "distribution" that is a slightly different matter.

[Kawatta-kun]

Just wnated to know, for some of my MAC friends.
Using AMVapp and all it's possibilties, it's easy, but for windows. How do MAC people do for themselves? Start to end, please...

[post-it]

Just wnated to know, for some of my MAC friends.
Using AMVapp and all it's possibilties, it's easy, but for windows. How do MAC people do for themselves? Start to end, please...

X2

I'm seriously looking at dropping Win 7 64-bit and loading Snow onto this CQ56.
.. in order to switch, I need to know that I can
1) DVD rip to "whatever is understood by MAC's Editors"
2) have at least one LossLess Codec which is understood "by that editor"
3) when finished, to have something like Zarx264GUI to help "encode the FINAL presentation".

I normally don't use much, so far; only a Utube downloader and Safari.

..? .. anything else needed?

and, yes; I'm quite serious about switching systems!

[Kariudo]

Just wnated to know, for some of my MAC friends.
Using AMVapp and all it's possibilties, it's easy, but for windows. How do MAC people do for themselves? Start to end, please...

read the first post -_-

[TEKnician]

Just wnated to know, for some of my MAC friends.
Using AMVapp and all it's possibilties, it's easy, but for windows. How do MAC people do for themselves? Start to end, please...

read the first post -_-

ROFLMAO FAIL

I don't care if i don't even fully understand avisynth yet, that was just priceless. I mean, WHAT THE HELL IS THE NAME OF THIS TOPIC? omfg gtfo...

[TEKnician]

Wat the F***? I DIDN'T EVEN DO ANYTHING!!!

[TEKnician]

Disregard...somehow i fix'd it and i'm NOT going to touch whatever i did.

[Anicsi]

I have some old amvs that I would like to polish up with avisynth, to see what I can make of the sort of bad quality. I've never used avisynth before, though, so I am not familiar with the process. Naturally I've read through the topic, but I wanted to ask what the steps for post-processing rather than pre-processing are.

1. I have MPEGstreamclip and Perian. I don't assume I need the ripper, since it's only for DVDs. Which would be a better program to install if I only need it for cleaning? WINE or Crossover?

2. So when I have everything installed, where do I go from there? The amvs I want to post-process have various formats, the early ones are .dv, after that most are H.264 .mov or .mp4. I need to end up with an avs file to write the commands, no? Since I don't have any VOB files to open, how do I get those?

I'd be very thankful about a reply!